Latest Articles in Auto Glass

  • 2004-07 BMW 5 Series, M5
    Windshield removal and replacement instructions
    December 21, 2011
    Under the driver-side wiper is a spacer “donut” that must be removed to allow for cowl removal. It is pressure-fit into place and will be hard to remove. We grasped the spacer with a locking wrench and wiggled it off the post. Also note that the interior garnish moldings are covered with fabric and subject to damage if the cutting blade makes contact with the fabric. Either remove or displace the...

  • In remembrance of Equalizer Industries' Ray Asbery
    November 3, 2011
    The auto glass industry lost an innovator, leader and friend this past September, when Equalizer Industries’ Ray Asbery passed away suddenly Sept. 27, 2011, at the age of 67.

  • 2011 GMC Terrain
    Windshield removal and replacement instructions
    November 3, 2011
    The urethane bead securing the windshield is a little thick along the sides and top. If using a cold knife to cut out the glass, you might need to use a blade that is the next size up in length. Also note, the top gap is close to the pinchweld wall, so care must be taken during cutout to avoid damaging the pinchweld wall.

  • 2011 Acura TL
    Windshield and front door glass removal and replacement instructions
    November 2, 2011
    The side moldings on this vehicle use the gradating clip system employed by Honda vehicles. These clips posed problems when they were first introduced and are still difficult to release without damage. However, with practice and patience, they are salvageable.

  • 2008-11 BMW 128i

    Quarter glass removal and replacement instructions
    September 26, 2011
    The following installation was performed on a 2008 vehicle, but all models in the BMW 1 Series through 2011 use this quarter glass. Before beginning the quarter glass removal, make sure you have the right trim for the vehicle. The part comes with flat black, glossy black and chrome lower trim. 

  • 2007-10 Audi Q7
    Windshield removal and replacement instructions
    September 26, 2011
            © 2011 National Glass Association. All rights reserved. Visit GlassMagazine.com for glass removal and replacement instructions for more than 450 vehicles. To sign up to receive the For Technicians Only e-bulletin, email FTO@glass.org. Vehicle type: Four-door utility vehicleNAGS numbers*: Windshield part numbers FW02637 solar, upper and lower molding...

  • 2011 Nissan Sentra
    Windshield removal and replacement instructions
    August 16, 2011
    The A-pillar molding on this vehicle extends from the fender to the back glass and is clipped down with a two-clip system: one clip attached to the body and one inserted into the molding. There are two ways to release the molding from the vehicle: pry out the molding clip from the body clip, or slide the molding from the clips. The latter method might prevent damage to the clips. 

  • 2011 Buick Regal
    Windshield removal and replacement instructions
    August 16, 2011
    There is plenty of room to use a cold knife to cut out the windshield on this vehicle; however, due to the U-shaped molding, it is recommended that a power tool not be used for interior cutout. Also watch for the lower cowl retainer. It is a little tight, so take care during removal to avoid damaging the cowl flange. Lastly, check the molding on the new windshield. The molding on the new part...

  • Tech tip: Re-installing the OnStar FMV Mirror
    July 18, 2011
    OnStar officials recently introduced the OnStar FMV rearview mirror that aftermarket consumers can purchase at OnStar FMV authorized retailers. In conjunction with the product introduction, OnStar is reaching out to manufacturers, distributors and installers of replacement auto glass to inform them of the proper procedure for re-installing the OnStar FMV Mirror.The majority of the OnStar FMV...

  • 2011 Nissan Titan
    Windshield removal and replacement instructions
    July 18, 2011
    When removing the cowl panel, you will need to release the eight retainers on the underside of the panel using a door pad tool or long pry tool. Be careful, as these retainers can break in cold weather. Also watch out for the top and side molding. It is a wraparound U-channel type that has a metal core, and removing it will be the hardest part of the job. It will need to be replaced, so you can...
Page 2 of 74
 << First | < Previous | 1 | 2 | 3 | 4 | 5 …| Next > | Last >> 

What's Hot

  • Redefining the interior
    This commercial office space in Tulsa, Okla., features a 42-foot-long, custom, continuous art mural that spans 14 glass panels. 
    Great Glazing: Custom interior officeThis commercial office space in Tulsa, Okla., features a 42-foot-long, custom, continuous art mural that spans 14 glass panels suspended from the ceiling. Created by Tulsa artist May Yang, the mural is based on local Oklahoma themes, transitioning from rural landscape to the Tulsa skyline.   Great Glazing: Joliet Junior College Campus...
  • Top Metal Companies
    A look at the leading manufacturers and fabricators of metal products, broken down by sales volume, number of locations and product offering. 
    Building on the success of the Top Glass Fabricators rankings introduced last year, Glass Magazine is expanding its coverage to include the Top Metal Companies, featuring the leading manufacturers and fabricators of metal products in the United States and Canada. The Top Metal Companies include those that manufacture, fabricate and sell curtain wall, storefront and entrance, commercial interior...
  • 2012 Glass Magazine Award Winners: The People
    Read about the winners
    In an effort to spotlight the people who make the Glass Magazine Award-winning products and projects possible, this year’s program included people-centric categories, for which the industry submitted their picks for best installer, production supervisor, project manager and sales rep.After narrowing down the nominations to three finalists in each category, the Glass Magazine editors asked the...